How to use SEC-E9 to cut T60 keys by using the dimple key clamp?

Here is the step-by-step guide for sec-e9 key cutting machine owners to cut T60 key by using the dimple key clamp.


Device:


SEC-E9 key cutting machine

T60 key

Blank new key


Steps to cut T60 keys by SEC-E9 :


Step 1: Decode original key number


Press the “Dimple” button and select “T” “Teas” “T60” to enter the key data



Press “Decode”, then the original key can open cylinder




Fix the original key on top level of the dimple clamp

Note: Please pay attention to the key position



Press “Decode” button to start decoding original key and get the key numbers




Press “Cut” button to enter cutting page


Step 2: Cut new blank key


Fix the new key blank on top level of the dimple clamp

Please pay attention to the key position




Press “Cut” button to start cutting a new key (side A) with SEC-E9

Note: Please remember to close the safe gate




Done with side A

Open the safe gate to clean the clamp& the new key

Then take out the new key

Put side B on the dimple clamp, pay attention to the key position

Repeat the same above operating step as side A to cut side B


Cutting is done!

Open the safe gate to clean the clamp& the new key

Remove the new key

Test the new key, work very well!





Comments

  1. adminJanuary 23, 2020 at 2:07 AM

    Found very informative knowledge. Keep sharing such informative knowledge. Most of the time we need emergency locksmith when we are in hurry. Always look for best locksmith near you who responds you fast and quick.

    ReplyDelete

Post a Comment

Popular posts from this blog

How to Update SEC-E9 key cutting machine

Image
SEC-E9 key cutting machine latest update and how to upgrade EB and EU Version.  Latest SEC-E9 tablet update info (Released on 12th June, 2019) 1)Software Version: 16.0.0.4, DB version: 15.18 2)Newly added key data includes: 1. Toyota-Corolla 2015 VA2 8 cuts laser key (IC card 1423) 2. Ford-Fiesta 2017 HU198T 10cuts inner groove laser key(IC card 1434) 3. Dacia /Renault HU136 8cuts double side key(IC card 1891) 4. New Volkswagen and Audi HU162t 10cuts(IC card 1421) 5. Mazda 10cuts double side key(IC card 20131) 6. Mercedes HU64 key(IC card 20123) 7. Lada single-side key and double side key and code 8 .Triumph motorcycle key and code 3)Improved key data includes: 1. Improve Lexus, Chevrolet , Subaru menu: add new choices of manufacture year in and after 2015. 2. Improve Lexus, Chevrote, subaru key and key code 3. Improve Arco Rifkin (Rifkin), Rolls-Royce, MG, Ssangyong, House key, Aprilia (motorcycle) code How to upgrade SEC-E9 Tablet PC (EB a...
Read more

How to use SEC-E9 to calibrate single-sided key clamp?

Image
Here is the step-by-step guide for SEC-E9 owners to use SEC-E9 key machine to calibrate single-sided key clamp. Step 1: Calibrate automobile key clamp Install automobile key clamp on SEC-E9 Insert two decoders into the machine Press “setup” and “First step” button to enter the “Clamp Calibration” interface Note: It is a very important step to press “first step”, please don’t miss it. Press “start” button to calibrate the distance between decoder and cutter Fix calibration block on the top level of clamp and pay attention to the position Click the picture to continue… According to the prompt, then click the picture to continue again Step 2: Calibrate single sided standard key clamp Take out automobile key clamp Install single sided standard key clamp Press “single sided standard key clamp” and make sure 3.5mm side faces inside. Tighten the holder Click the picture to continue… Step 3: Calibrate decoder and cutter length of single sided key clamp Go back to home page and ent...
Read more

How to Cut HU66 Key By SEC-E9

Image
How to Cut HU66 key by using HU66 auxiliary clamp on SEC-E9 key cutting machine . Procedures: Go to SEC-E9 menu Press “Search” button Select “SILCA” to enter key data Use the original key to open cylinder Test OK Use the stopper to help you fix the original key in the correct position Press “Decode” button to start decoding original key and get the key number Get the key number successfully Put the key into the HU66 auxiliary fixture and tighten Select “Cut”-> “1 st  Cut” to start cutting a new key Note: Please remember to close the safe gate It takes about 2 minutes to cutting the key Cutting is done! Open the safe gate to clean the clamp & the new key Take out the new key Fix the other side of the new key blank Press “2 nd  cut” button to start cutting another side key Cutting is complete Test the new key, can work very well!
Read more