SEC-E9 Cut 2018 VW/Audi HU162T Keys

How to Cut 2018 VW/ Audi HU162T keys by SEC-E9 Key Cutting Machine.

 Procedures:

 Prepare the key and cylinder for new VW HU162T (9)


Press “Search” button in the main interface
Select “Key blank”-> Input “HU162T”
Press “Search”-> Select “SILCA-HU162 (9)


Come to the basic data page for HU162T
Firstly decode side A of original key


Fix the side A of original key on#1 car key clamp


Confirm it’s side A, and then press “Decode”


Decoding side A


Side A is decoded successfully


Press the key image to decode side B of the original key
Note: There is a small groove on side B


Fix side B on HU162T clamp, and tighten the screw


Install HU162T onto #1 car key clamp
Press “Decode” button to enter decoding page
Select the most right blue icon as sense key location and check “Round off”


Decoding side B
Complete decoding side B


Remove HU162T clamp and put a new key blank for copy


Select side A, and press “Cut” button to enter cutting page
Replace the right decoder with a 1.9mm cutter
Note: Remember use 1.9mm cutter to cut HU162T keys on #1 car key clamp
Cutting side A


Finish cutting side A
Clean the clamp and blank key
Fix the other side of the blank key
Select side B by press the key image
Press “Cut”
Remember to cut side B with 2.0mm cutter on #1 car key clamp


Install HU162T clamp to cut side B
Cutting side B is done
Clean the clamp and blank key
Remove HU162T clamp and prepare to cut side C on #1 car key clamp
Cutting side C is done


Use it to open the cylinder successfully!


Comments

Post a Comment

Popular posts from this blog

How to Update SEC-E9 key cutting machine

Image
SEC-E9 key cutting machine latest update and how to upgrade EB and EU Version.  Latest SEC-E9 tablet update info (Released on 12th June, 2019) 1)Software Version: 16.0.0.4, DB version: 15.18 2)Newly added key data includes: 1. Toyota-Corolla 2015 VA2 8 cuts laser key (IC card 1423) 2. Ford-Fiesta 2017 HU198T 10cuts inner groove laser key(IC card 1434) 3. Dacia /Renault HU136 8cuts double side key(IC card 1891) 4. New Volkswagen and Audi HU162t 10cuts(IC card 1421) 5. Mazda 10cuts double side key(IC card 20131) 6. Mercedes HU64 key(IC card 20123) 7. Lada single-side key and double side key and code 8 .Triumph motorcycle key and code 3)Improved key data includes: 1. Improve Lexus, Chevrolet , Subaru menu: add new choices of manufacture year in and after 2015. 2. Improve Lexus, Chevrote, subaru key and key code 3. Improve Arco Rifkin (Rifkin), Rolls-Royce, MG, Ssangyong, House key, Aprilia (motorcycle) code How to upgrade SEC-E9 Tablet PC (EB a...
Read more

How to use SEC-E9 to calibrate single-sided key clamp?

Image
Here is the step-by-step guide for SEC-E9 owners to use SEC-E9 key machine to calibrate single-sided key clamp. Step 1: Calibrate automobile key clamp Install automobile key clamp on SEC-E9 Insert two decoders into the machine Press “setup” and “First step” button to enter the “Clamp Calibration” interface Note: It is a very important step to press “first step”, please don’t miss it. Press “start” button to calibrate the distance between decoder and cutter Fix calibration block on the top level of clamp and pay attention to the position Click the picture to continue… According to the prompt, then click the picture to continue again Step 2: Calibrate single sided standard key clamp Take out automobile key clamp Install single sided standard key clamp Press “single sided standard key clamp” and make sure 3.5mm side faces inside. Tighten the holder Click the picture to continue… Step 3: Calibrate decoder and cutter length of single sided key clamp Go back to home page and ent...
Read more

How to Cut HU66 Key By SEC-E9

Image
How to Cut HU66 key by using HU66 auxiliary clamp on SEC-E9 key cutting machine . Procedures: Go to SEC-E9 menu Press “Search” button Select “SILCA” to enter key data Use the original key to open cylinder Test OK Use the stopper to help you fix the original key in the correct position Press “Decode” button to start decoding original key and get the key number Get the key number successfully Put the key into the HU66 auxiliary fixture and tighten Select “Cut”-> “1 st  Cut” to start cutting a new key Note: Please remember to close the safe gate It takes about 2 minutes to cutting the key Cutting is done! Open the safe gate to clean the clamp & the new key Take out the new key Fix the other side of the new key blank Press “2 nd  cut” button to start cutting another side key Cutting is complete Test the new key, can work very well!
Read more